2/18/2024 0 Comments Hp photosmart b209a inkTouch the electrical contact areas only with the cleaning materials. Plastic ramp on the side of the ink nozzlesĭo not touch the nozzles or the electrical contacts with your fingers. Review the three areas of the printhead that need to be cleaned.įigure : Example of the three areas to clean on the printhead Lift up to remove the printhead from the ink carriage. Lift the latch handle on the ink carriage until it stops.įigure : Lifting the ink carriage latch handle Search Windows for your printer model name, and click the printer name in the list of results.Ĭlick Settings, and then under Print Settings, click Printer Toolbox.Ĭlick Clean the Printhead, then follow the onscreen instructions. If any ink cartridges protrude, press down firmly until each ink cartridge snaps into place.Ĭheck the printer control panel display for the error message.Ĭlean the printhead with an automated tool Run your finger along the top of the ink cartridges to make sure none of them protrude. Make sure each colored dot on the ink cartridge label matches the colored dot on the carriage.įigure : Reinserting the ink cartridge into the correct slotįigure : Example of snapping the ink cartridge into place Use a fresh, lightly dampened, lint-free cloth to wipe any accumulated ink and debris on the copper-colored contact on the ink cartridge.įigure : Example of the copper-colored contact on the ink cartridgeĬarefully reinsert one of the ink cartridges into its slot, and then push the ink cartridge down and forward until it snaps into place. If any of the ink cartridges have clogged vents, use a pin to clean the vents. Examine the vent area located on top of the ink cartridge, next to the HP logo.If an orange tab is attached to any ink cartridge, remove it. Doing so can result in damage to both the printer and the ink cartridges. Place the ink cartridges on a clean piece of paper with the ink opening pointing up.ĭo not leave the ink cartridges outside the printer longer than 30 minutes. To remove the ink cartridge, press the tab on the front of the ink cartridge to release it, and then remove it.įigure : Example of removing an ink cartridge from the printhead Wait until the warm-up period finishes and your printer is idle and silent before you proceed.Ĭlean the ink cartridge vents and contactsĭo not use tap water because it might contain contaminants that can damage the printhead. The printer lights might flash, and the carriage might move. The printer might go through a warm-up period. Turn on the printer, if it does not automatically turn on. Reconnect the power cord to the rear of the printer. HP recommends connecting the printer power cord directly to the wall outlet. Plug the power cord back into the wall outlet. Unplug the power cord from the wall outlet. With the printer turned on, disconnect the power cord from the rear of the printer. Wait until the printer is idle and silent before you continue. Turn the printer on, if it is not already on. How is the printer connected to computer, wired or wireless? However, I will need a few details to provide an accurate solution,ĭid you do any hardware or software changes? Chinese to the HP Forums, this is a great location to get assistance! I read your post and see that you are getting Error code 0xC19A0022 on your printer. I would like to help you resolve this issue.Business PCs, Workstations and Point of Sale Systems.Printer Wireless, Networking & Internet.DesignJet, Large Format Printers & Digital Press.Printing Errors or Lights & Stuck Print Jobs.Notebook Hardware and Upgrade Questions.If the information I've provided was helpful, give us some reinforcement by clicking the "Solution Accepted" and this will also help other community members with similar issue. If the issue persists, please follow the instructions in Step 4 to ensure the cartridges are well vented and then Step 6 to Manually clean the Printhead. The printer prints a test page when the printhead cleaning completes. Search Windows for your printer model name, and click the printer name in the list of results.Ĭlick Settings, and then under Print Settings, click Printer Toolbox.Ĭlick Clean the Printhead, then follow the onscreen instructions. I appreciate all your efforts and expertise in troubleshooting this issueĭid you clean the Printhead using the Automated Tool? I understand that your HP Photosmart printer is giving the Oxc19a0020 Ink System Failure error A really great platform for posting all your questions and finding solutions.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |